Fs 1020d manual

Clean the charger wire. Remove the process unit from the printer and slide the charger knob back and forth to clean the charger wire. See Chapter Check the operator panel.

Page 29 See Chapter Clean the charger wire. See Chapter Try setting the thin paper mode. Page 30 Printed Results Characters out of position. Table Continued Corrective Action Check the file or program. If the problem occurs only with a specific file or program, the most likely cause is an error in a parameter to a command or command syntax. This section explains the indicators on the operator panel and the appropriate corrective action to take in each case.

Page Maintenance Messages When you want to feed from a other paper source, press the key to switch the paper source. The printer prints on the paper size and type set in that particular paper source.

The cassette paper size and data paper size are not the same. Page 33 After reinserting the paper cassette, you should be able to print. There is no more toner in the toner container. The printer has stopped because there is no more toner.

Replace with a new toner kit. After replacing, be sure to clean the printer. See There is no paper in the MP tray. Table When the following errors occur, turn off your printer, remove the plug from the AC outlet, and contact your Kyocera Mita dealer. The indicators are shown in two different states, according to the way they alternate.

Gently shake the process unit horizontally a few times, then reinstall it into the printer. If this error message does not disappear, contact your Kyocera Mita dealer less than , pages printing. Communication error F error Contact your Kyocera Mita dealer. Table Continued Page Error Messages You can abandon printing by pressing the Current print processing cannot continue due to complex data. The data transferred to the printer was too complex to print on a page.

Press the can abandon printing by the To release the page protect mode, send the following Page 38 Turn the power switch off and then on to restart the printer.

Page Normal Indicator Display When the printer is switched on for the first time after the toner container is installed, Adding toner also appears. The printer is warming up and is not ready to print. The indicators light in sequence twice from top to bottom. The printer will stop whenever paper jams in the printer or paper is not fed from a paper cassette.

The printer will go offline and indicator will light in the operator panel. Page Jam At The Paper Cassette Jam at the Duplexer Pull out the paper cassette and remove any partially fed paper, then re- close the paper cassette. The printer then automatically warms up and resumes printing.

Figure Insert the paper cassette into the slot in the printer. Page Jam Inside The Printer 3. Top Cover Figure Remove the process unit from the printer as shown in the figure. When a paper jam occurs in the MP tray, clear it using the following procedure. Page 46 A If the leading edge of the jammed paper has been fed further into the printer than the metal registration roller, remove the jammed paper by its leading edge. B If the paper has not been fed as far as the metal registration roller, remove the jammed paper from the MP tray side.

Page General Guidelines Paper Availability 4. Page Selecting The Right Paper Use of paper in these conditions can lead to illegible printing, misfeeding, and paper jams, and can shorten the life of the printer.

In particular, avoid using paper with a surface coating or other surface treatment. The paper should have as smooth and even a surface as possible. Page Paper Size 1 square meter.

Paper that is too light or too heavy can cause misfeeding, jams, and premature wear of the printer. Uneven paper weight can cause multiple feeds, print defects, poor toner fusing, blurring, and other print quality problems. Page Moisture Content When paper is manufactured, it is cut into sheets with the grain running parallel to the length long grain or parallel to the width short grain. Short grain paper can cause feeding problems in the printer. All paper used in the printer should be long grain.

Page 52 Porosity: Refers to the density of the paper structure; that is, to how openly or compactly the fibers are bonded. Stiffness: Limp paper can buckle inside the printer, while paper that is too stiff may bind. Either way the result is a paper jam. Page Special Paper No liability will be assumed if moisture and so forth given off during printing on special paper causes harm to the machine or operator.

Before purchasing any type of special paper, test a sample on the printer and check that printing quality is satisfactory. Page Adhesive-Backed Labels Adhesive-Backed Labels The basic rule for printing on adhesive labels is that the adhesive must never come into contact with any part of the printer. Adhesive paper sticking to the drum or rollers will damage the printer. Label paper must be manually fed. Envelopes must be manually fed. An envelope is a more complex object than a single sheet of paper.

For this reason, it may not be possible to obtain consistent printing quality over the entire envelope surface. Page Thick Paper Recycled Paper Select recycled paper that meets the same specifications as the white bond paper see Table Before purchasing recycled paper, test a sample on the printer and check that the printing quality is satisfactory.

Feeding rough edged on page Do you have a question about the Kyocera FSD or do you need help? Ask your question here. Provide a clear and comprehensive description of the issue and your question. The more detail you provide for your issue and question, the easier it will be for other Kyocera FSD owners to properly answer your question. View the manual for the Kyocera FSD here, for free. This manual comes under the category Printers and has been rated by 2 people with an average of a 8.

This manual is available in the following languages: English. Below, you will find the most frequently asked questions about the Kyocera FSD. Is your question not listed? Ask a question. About the Kyocera FSD. Revision 1. The Programs are licensed not sold. IBM, or the applicable IBM country organization, grants you a license for the Programs only in the country where you acquired the Programs.

You obtain no rights other than those granted you under this license. IBM retains title to the Programs. IBM owns, or has licensed from the owner, copyrights in the Programs. Under this license, you may use the Programs only with the device on which they are installed and transfer possession of the Programs and the device to another party.

If you transfer the Programs, you must transfer a copy of this license and any other documentation to the other party. Your license is then terminated. The other party agrees to these terms and conditions by its first use of the Program. Some jurisdictions do not allow the exclusion of implied warranties, so the above exclusion may not apply to you.

This limitation will not apply to claims for bodily injury or damages to real or tangible personal property for which IBM is legally liable. IBM will not be liable for any lost profits, lost savings, or any incidental damages or other economic consequential damages, even if IBM, or its authorized supplier, has been advised of the possibility of such damages.

IBM will not be liable for any damages claimed by you based on any third party claim. This limitation of remedies also applies to any developer of Programs supplied to IBM. Such developer is an intended beneficiary of this Section. Some jurisdictions do not allow these limitations or exclusions, so they may not apply to you.

You may terminate your license at any time. IBM may terminate your license if you fail to comply with the terms and conditions of this license. In either event, you must destroy all your copies of the Program. You are responsible for payment of any taxes, including personal property taxes, resulting from this license.

Neither party may bring an action, regardless of form, more than two years after the cause of action arose. If you acquired the Program in Canada, this license is governed by the laws of the Province of Ontario. Otherwise, this license is governed by the laws of the country in which you acquired the Program.

Agfa Japan retains all rights, title and interest to the Software and Typefaces and no rights are granted to you other than a License to use the Software on the terms expressly set forth in this Agreement.

This License may be terminated by Agfa Japan if you fail to comply with the terms of this License and such failure is not remedied within thirty 30 days after notice from Agfa Japan. When this License expires or is terminated, you shall either return to Agfa Japan or destroy all copies of the Software and Typefaces and documentation as requested.

Further use, duplication or disclosure is subject to restrictions applicable to restricted rights software as set forth in FAR Dangerous sparks may cause burn. And make sure not to stick to your skin. Or dispose of the toner or toner containers in accordance with Federal, State and Local rules and regulations.

Guide to the Manuals Guide to the Operation Guide Basic Operations Operator Panel Chapter Toner Container Container Replacement Interval. Cleaning the General Guide Print Quality Requiring Service Personnel Attention. Indicator Display. Paper Jam Inside the Printer. Chapter 4 Paper Selection General Guidelines Selecting the Right Paper Special Paper Paper Type Chapter 5 Fonts Internal Fonts List of Fonts Appendix A Options Available Options Expansion Memory Installation Memory CompactFlash Card Network Interface Card Appendix B Host Computer Interface Parallel Interface Interface Signals USB Interface Serial Interface Option RSC Protocol RSC Cable Connection The Kyocera Mita page printer has many desirable features, such as the duplex printing mode which lets you print onto both sides of the paper and an Auto Media Type Selection function that automatically selects the media before printing.

This Operation Guide guides you through the following topics:. This chapter describes the names and functions of the keys and indicators on top of the printer. This chapter explains how to replace the toner container and how to care for your printer.

This chapter explains how to handle printer problems that may occur, such as paper jams. The operator panel on top of the printer consists of four indicators and two keys. The keys perform operations, such as canceling data, switching the printer mode between online and offline status, and printing status pages.

The numbers used in the above figure are referred to in the Reference column of the table on the following page. Refer to the following table for the name and description of each indicator. The same indicator can have a variety of meanings, depending on the speed at which it is flashing. For details, see Chapter 3. The following is the printout of a typical standard status page. Its contents are explained in detail on the next page.

This information shows the software firmware version and date of issue of the printer. This information shows the currently selected paper source indicated by an asterisk , paper size, and various other printer settings. This information shows the currently selected resolution, number of copies printed to date, and the total page count.

This shows the IP address, subnet mask address, default gateway address and other settings for the network interface card installed in the printer. This information shows the amount of total memory installed in the printer, the amount of currently available memory, and the current status of the RAM disk. This shows all available emulations and the currently selected emulation marked with an asterisk.

The printer is shipped from the factory with PCL 6 emulation selected. The most recent error is displayed on the top line of the Error Log. For error remedies, see Chapter 3. This shows the approximate level of remaining toner. When the value is , the toner container is full. The closer to 0, the smaller the amount of remaining toner. This information shows all interfaces installed in the printer and the currently selected interface marked with an asterisk.

The Font section shows the font that is automatically selected when the printer starts up default font. It is possible to set different default fonts for each interface. This chapter explains how to replace the toner container and how to clean parts such as the registration roller and charger wire. When the printer runs low on toner, the toner indicator flashes on the operator panel.

Be sure to promptly replace the toner container and clean the inside of the printer when this message appears. If the printer stops printing while the toner indicator is lit, replace the toner container to continue printing.

The kit supplied with the printer only contains the toner container and wiper cloth. For details, see section 2. Plastic Bag. This ensures that the toner is evenly distributed inside. Lock lever 2 is automatically locked. To reset the toner counter, next time you turn.